DLDH PLUS

SAJ

spanish homologation
S33DLDH005001

Zero grazer agricultural trailers Juscafresa.

Destined for mowing and forage transport.

Stands out for its system that starts with the movement of the plates that creates air turbulance that helps to move the feed into the bottom of the elevator. During the mower operation, the elevator put the forage on the front part of the trailer, and then the floor chains moves the material from the front to the back part of the trailer.

Standard equipped with:     
Hydraulic installation system to use the elevator and the dispenser motors with refrigeration system
Bilateral unloading by rubber conveyor chains 2360x900 mm with hydraulic displacement to the back part and hydraulic motor for its working 
Dispenser provides continuous distribution for the unloading by two hydraulic motors, with electrohydraulic pressure switch that controls the advance of the floor chains
Cutting width 2100 mm
Hydraulically displaceable drawbar
ECI100: Square rocker axle 100 mm, 1900 track, 10 bolts, brakes 400x80  

Capacity: 23 - 33m3

MODELS

S23DLDH

S28DLDH

S33DLDH

23,00m3

28,00m3

33,00m3

 
S28DLDH
S23DLDH
S28DLDH
S33DLDH
M3
23
28
33
A
9360
10360
11360
B
5490
6490
7490
C
2550
2550
2550
D
1900
1900
1900
E
2820
3320
3820
F
1360
1360
1360
G
3600
3600
3600
H
550
550
550
I
1300
1300
1300
J
3020
3020
3020
K
2100
2100
2100
L
2000
2000
2000
N
860
860
860
O
4780
5780
6780
Q
3220
3220
3220

Descriptions, data and illustrations are only indicative. Juscafresa reserves the right to make any changes without prior notification.

 

Mowing system

The process consists of cutting the fodder by the mower plates which at the same time makes an air turbulence that helps the entrance of the fodder to the bottom of the elevator.

 

The elevator has the function of raising the cut forage towards the front part of the trailer where the material will accumulate and will move towards the rear by the drag chains.

work saj

Plate mower

The top plate has three blades that create air turbulance that helps to move the feed into the bottom of the elevator. 

The lower plates are entirely independent from the top plates and turning by the friction on the ground.

plato segadora

Mower

Mower with 1900mm of cutting width 

segadora 2100

Hydraulic independent system

Hydraulic independent system to use the elevator and dispenser.

The mower has one or two springs providing suspension so it can adapt to the terrain, and therefore avoid excessive friction of the plates on the ground.

instalacion hidraulica

Elevator

The feeder is raised by 6 ou 8 teeth and guided by channels, passing between the blades until the ejection in the body of the trailer. The tines are forked so they can pass through the cutting blades.

noria

Unloading

Bilateral unloading by rubber conveyor chains 2360x900 mm with hydraulic displacement to the back part and hydraulic motor for its working.
Hydraulic unloading by floor chains by a hydraulic reducer.

The discharge platform moves hydraulically by hydraulic cylinder, being able to choose how to download: back, left or right side.

Dispenser provides continuous distribution for the unloading by two hydraulic motors, with electrohydraulic pressure switch that controls the advance of the floor chains.

The dispenser work as fodder on the discharge platform obtaining a continous and uniform distribution. It incorporates a displacement system at the back, which is activated during the download process by easing the fodder pressure during the charge process, and avoid possible blockage at the time of starting the rotation of the distribution chains of the dispenser. 

The dispenser incorporates chains with spikes that start scraping the fodder inside the trailer, elevating to the top of the rotation of the chains and falling back on the discharge platform or the ground.

Automatic synchronizing for the unloading and security synchronization to avoid compressions on the dispenser.

descarga dldh plus

Drive shaft 

Homokinetic joint front transmission and friction disk clutch.

Back standard transmission and homokinetic joint.

7G7R071CE007W14
7G5R061CEWR7Q11
7G5R061CEWR7Q11

Hydraulic kit

Electro-valves with control button box by cable to operate all the functions.

electrovalvulas

Button control

Button control with cable connection for all functions.

Automatic synchronizing for the unloading and security synchronization to avoid compressions on the dispenser.

Optional weighing system with load cells.

digi mando

Drag system

Equipped with 4 chains 80/12X manufactured with 20Mn4+S355JO.

cadena 8 12 12X

Drawbar

Hydraulically displaceable drawbar.

lanza 33

Towing eye Scharmüller

208284
208092
207909

Revolving ring towing eye 208284 Scharmüller ISO 20019

Fixed ring towing eye 208092 Scharmüller ISO 20019 

Ball towing eye 207909 Scharmüller ISO 24347

Axle

Square rocker axle 100 mm, 1900 track, 10 bolts, brakes 400x80.

E100

Optional wheels

S23DLDH
S28DLDH
S33DLDH
560/45 R 22,5
O
O
O

“A higher quality finish means more machine life”

The Juscafresa finishing process is:

-Polishing of the whole machine removing the impurities that persist in the metal.

 

-Pressurized washing with degreaser solution to obtain a better grip on the primer and prevent corrosion.

 

-Wash at high pressure with hot water to remove dirt from the metal and remains of adhered products.

 

-Application of a high quality primer layer.

 

-Application of two layers of Juscafresa paint specially designed with our corporate color.

acabado metal juscafresa

Descriptions, data and illustrations are only indicative. Juscafresa reserves the right to make any changes without prior notification.

 
1/10
 
chat

Questions?
Talk to a chat specialist or send an email to info@juscafresa.com.

​more information >

export mundial

International export
We ship to all continents and offer fast after-sales service.

​more information >

de lage landen

Financing options
Check our financing plans through the financial De Lage Landen

​more information >