spanish homologation

Zero grazer agricultural trailers Juscafresa.

Destined for mowing and forage transport.

Stands out for its system that starts with the movement of the plates that creates air turbulance that helps to move the feed into the bottom of the elevator. During the mower operation, the elevator put the forage on the front part of the trailer, and then the floor chains moves the material from the front to the back part of the trailer.

Standard equipped with:     
Hydraulic installation system to use the elevator and the dispenser motors
Bilateral unloading by chains 2160x900 mm and with hydraulic displacement to the back part by hydraulic motor 
Dispenser provides continuous distribution for the unloading by hydraulic motor
Automatic synchronizing for the unloading and security synchronization to avoid compressions on the dispenser
Cutting width 1900 mm
Hydraulically displaceable drawbar
EBI70: Rocker axle 70 mm, track 1520, 6 bolts, brakes 300x60 

Capacity: 14 - 17m3

MODELS

S14DLDH

S15DLDH

S17DLDH

14,00m3

15,00m3

17,00m3

 
S14DLDH
S14DLDH
S15DLDH
S17DLDH
M3
14
15
17
A
7840
8340
8840
B
4720
5240
5740
C
2320
2320
2320
D
1520
1520
1520
E
2710
2860
3010
F
1180
1180
1180
G
3120
3120
3120
H
450
450
450
I
900
900
900
J
2570
2570
2570
K
1900
1900
1900
L
1800
1800
1800
N
720
720
720
O
4040
4540
5040
P
7230
7730
8230
Q
2950
2950
2950

Descriptions, data and illustrations are only indicative. Juscafresa reserves the right to make any changes without prior notification.

 

Mowing system

The process consists of cutting the fodder by the mower plates which at the same time makes an air turbulence that helps the entrance of the fodder to the bottom of the elevator.

 

The elevator has the function of raising the cut forage towards the front part of the trailer where the material will accumulate and will move towards the rear by the drag chains.

work saj

Plate mower

The top plate has three blades that create air turbulance that helps to move the feed into the bottom of the elevator. 

The lower plates are entirely independent from the top plates and turning by the friction on the ground.

plato segadora

Mower

Mower with 1900mm of cutting width 

Hydraulic independent system

Hydraulic independent system to use the elevator and dispenser.

The mower has one or two springs providing suspension so it can adapt to the terrain, and therefore avoid excessive friction of the plates on the ground.

instalacion hidraulica

Elevator

The feeder is raised by 6 ou 8 teeth and guided by channels, passing between the blades until the ejection in the body of the trailer. The tines are forked so they can pass through the cutting blades.

noria

Unloading

Bilateral unloading by chains 2160x900 mm and with hydraulic displacement to the back part by hydraulic motor.

The discharge platform moves hydraulically by hydraulic cylinder, being able to choose how to download: back, left or right side.

Dispenser provides continuous distribution for the unloading by hydraulic motor.

The dispenser work as fodder on the discharge platform obtaining a continous and uniform distribution. It incorporates a displacement system at the back, which is activated during the download process by easing the fodder pressure during the charge process, and avoid possible blockage at the time of starting the rotation of the distribution chains of the dispenser. 

The dispenser incorporates chains with spikes that start scraping the fodder inside the trailer, elevating to the top of the rotation of the chains and falling back on the discharge platform or the ground.

Automatic synchronizing for the unloading and security synchronization to avoid compressions on the dispenser.

Optional:

Bilateral unloading by conveyor belt 2160x900 mm and with hydraulic displacement to the back part by hydraulic motor

descarga dldh

Drive shaft 

Homokinetic joint front transmission and friction disk clutch.

Back standard transmission and homokinetic joint.

Hydraulic kit

Electro-valves with control button box by cable to operate all the functions.

electrovalvulas

Button control

Button control with cable connection for all functions.

Automatic synchronizing for the unloading and security synchronization to avoid compressions on the dispenser.

Optional weighing system with load cells.

digi mando

Drag system

Equipped with oval chains of 10mm.

Drawbar

Hydraulically displaceable drawbar.

Towing eye Scharmüller

Revolving ring towing eye 208857 Scharmüller  ISO 5692-2

Ball towing eye 208864 Scharmüller ISO 24347

Axle

Square rocker axle 70 mm, 1520 track, 6 bolts, brakes 300x90.

Optional wheels

S14DLDH
S15DLDH
S17DLDH
480/45 - 17
O
O
O

“A higher quality finish means more machine life”

The Juscafresa finishing process is:

-Polishing of the whole machine removing the impurities that persist in the metal.

 

-Pressurized washing with degreaser solution to obtain a better grip on the primer and prevent corrosion.

 

-Wash at high pressure with hot water to remove dirt from the metal and remains of adhered products.

 

-Application of a high quality primer layer.

 

-Application of two layers of Juscafresa paint specially designed with our corporate color.

acabado metal juscafresa

Descriptions, data and illustrations are only indicative. Juscafresa reserves the right to make any changes without prior notification.

 
1/12
 
chat

Questions?
Talk to a chat specialist or send an email to info@juscafresa.com.

​more information >

export mundial

International export
We ship to all continents and offer fast after-sales service.

​more information >

Financing options
Check our financing plans through the financial De Lage Landen

​more information >